Special Report: How the New Micro-Particle Colloidal Silver Generator Differs From Conventional Colloidal Silver Generators
In the past, there have been only a few ways to achieve the production of silver micro-particles. These methods have proven to be expensive and time-consuming, requiring the use of equipment found only in professional laboratories. Colloidal silver manufacturers basically have to make batches of standard colloidal silver through a high-voltage process utilizing upwards of 10,000 volts, and then use expensive laboratory equipment to extract the particles from the solution and separate the larger from the smaller particles before reconstituting the smaller silver particles back into solution. Some colloidal silver manufacturers used a sophisticated centrifuge technology to achieve this. Others have used more conventional laboratory forms of separation such as filtration. There is also a `chemical milling' variation, where larger colloids are reduced in size with an acid bath. This is why commercial bottled colloidal silver products that truly contain micro-particles of silver are always very expensive to purchase as much as $59 for a tiny 8-ounce bottle.
On the other hand, thanks to an astonishing new breakthrough in colloidal silver-making technology, the new Micro-Particle Colloidal Silver Generator allows you to produce true micro-particle colloidal silver -- quickly and easily, in the comfort and privacy of your own home -- for about 36 cents a quart!.
Creating sub-microscopic silver micro-particles with a standard low-voltage DC-current colloidal silver generator was initially thought to be impossible. But what a bright electrical engineer named Paul Johnson discovered several years ago was the fact that you can do so, if you utilize a slower and more stable rate of silver particle production than what is normally used, while simultaneously eliminating excessive electrical conductivity in the water during the entire colloidal silver-making process. To accomplish this, you must be able to achieve five specific goals:
Built-in water resistance tester for making sure your water is non-conductive enough to produce silver micro-particles -- The built-in water resistance tester in the new Micro-Particle Colloidal Silver Generator allows you to know immediately whether the water you are using is superior non-conductive steam-distilled water, or inferior mineral-laden and highly-conductive water. If, at the very start of the colloidal silver-making process the green light on the Micro-Particle Generator box glows brightly, then the water is too highly mineralized (i.e., too conductive) for making silver micro-particles. If the green light on the box glows only dimly or even not at all, then you can rest assured that the water has low-to-no mineral content (i.e., extremely low conductivity) and is thus perfect for making silver micro-particles. In short, the built-in water resistance tester allows you to know right from the start whether or not the distilled water you are using is of a sufficiently high-quality to produce silver micro-particles. To our knowledge, no other colloidal silver generator on the market today provides you with this crucial benefit
Slower rate of production One of the most overlooked rules of making high-quality colloidal silver is that the faster your unit produces silver particles, the larger they will tend to be. Most standard colloidal silver generators are calibrated for greater speed of colloidal silver production, rather than for smaller particle size. The significantly higher voltage-to-amperage ratio used in standard colloidal silver generators literally "blows" chunks of silver off the positive silver electrode, rather than allowing very tiny particles to slowly trickle off. This automatically produces silver particles that are frequently too large for the human body to properly utilize. What's more, as these larger silver particles accumulate in the solution during the colloidal silver-making process, they vastly increase the electrical conductivity of the solution. This in turn increases the speed at which silver particles leave the positive silver electrode, which results in even larger silver particles entering the solution. In other words, it is a vicious cycle of ever increasing particle size. This is why the new Micro-Particle Colloidal Silver Generator utilizes a significantly longer running time (3 hrs.) for colloidal silver production, at a fraction of the voltage-to-amperage ratio used by the manufacturers of most standard colloidal silver generators. By dramatically reducing the voltage-to-amperage ratio, the silver particles merely trickle off the positive silver electrode at a much slower rate and at a dramatically smaller particle size right from the start. And they stay that way throughout the entire three-hour colloidal silver making process!
Built-in aerator (i.e., bubbler) -- The built-in aerator keeps the water fully aerated and agitated during the entire colloidal-silver making process. This has a very important three-fold purpose: First, the constant aeration and agitation of the water during the entire colloidal silver-making process helps prevent the agglomeration (i.e., bonding) of silver particles as they leave the positive silver electrode. With standard colloidal silver generators, the silver particles tend to accumulate in the water not far from the positive silver electrode, because there is no agitation of the water to cause their wider dispersal. From the very outset of the colloidal silver-making process this fosters particle agglomeration (i.e., the formation of larger silver particles through particle bonding). But with the new Micro-Particle Colloidal Silver Generator, the silver particles are immediately dispersed into wide circulation within the solution by the bubbling action of the built-in aerator. This makes it virtually impossible for silver particles to accumulate near the positive silver electrode and form larger particle agglomerates. Once the individual silver particles are dispersed throughout the solution, the positive electrical charge they carry becomes dominant, and they go into Brownian motion. In other words, from that point forward they are able to repel each other and remain suspended in the solution indefinitely without agglomerating!
Secondly, the constant aeration of the water helps break up the electrical "bridging" that always takes place between the positive and negative silver electrodes. "Bridging" simply means that silver particles tend to get caught in the electrical interplay between the two silver electrodes, and accumulate there, forming larger particle agglomerates that are difficult for the body to utilize. This is one of the biggest problems with standard colloidal silver generators. But the Micro-Particle Colloidal Silver Generator solves this problem completely by aerating and agitating the water constantly during the entire colloidal silver-making process. The "bridging" between the two silver electrodes is thereby broken up completely, and the resulting particle agglomeration is eliminated. While some manufacturers of colloidal silver generators utilize a clumsy motorized stirring mechanism to accomplish this, no other colloidal silver generator we know of does so as efficiently and effectively as the new Micro-Particle Colloidal Silver Generator, with its' built in aerator.
Third, the constant aeration of the water prevents excessive electrolysis from building up in the solution. This is important, because when using a standard colloidal silver generator, the electrical conductivity of the entire colloidal silver solution is increased dramatically as more silver particles enter the water. In turn, this increased electrical conductivity causes additional silver particles to be drawn from the positive silver electrode at a faster rate and at a significantly larger size. But because the new Micro-Particle Colloidal Silver Generator keeps the entire colloidal silver solution super-aerated during the colloidal-silver making process, the buildup of excessive electrical conductivity is dramatically mitigated. Why? Because air is one of nature's least conductive elements. Super-aerating the water prevents excessive electrical conductivity from building up, which in turn prevents additional silver particles from being drawn from the positive silver electrode at an excessively fast rate that results in excessively large particles. Only the new Micro-Particle Colloidal Silver Generator offers you this highly beneficial innovation!
A Brief Word About "Constant Current" Regulators…
Some colloidal silver generator manufacturers attempt to resolve the problem of electrolytic buildup in the colloidal silver solution by adding a complex piece of computer technology called a "constant current regulator" to their generators. This technology monitors the buildup of electrical conductivity in the colloidal silver solution, and concurrently reduces the generator's electrical current as electrolysis builds up in the solution. This works pretty good, to a certain extent. But it is an overly-complex technological solution to a very simple problem. By simply aerating the water to help prevent the buildup of excessive electrical conductivity, you altogether eliminate the need for complex computer technology in a colloidal silver generator. What's more, when someone adds relatively complex computer technology to a colloidal silver generator, the customer always ends up with one more highly sensitive electronic component that could burn out, short out, or otherwise go bad, and you'd never know it was not working. On the other hand, with the new Micro-Particle Colloidal Silver Generator, if the aeration goes out you know it immediately, because the bubbling will stop. In short, with the new Micro-Particle Colloidal Silver Generator you never have to worry about whether or not sensitive computer equipment has shorted out or is otherwise not working correctly due to moisture, overheating, power surges, being bumped or dropped, or for some other reason. With "constant current" generators, you are simply going by faith that everything is still working correctly. But with the new Micro-Particle Colloidal Silver Generator, if something goes wrong (and it rarely does), you will know it immediately, and we will fix it. Ours is a simple yet elegant solution to the problem of electrolytic buildup. Best of all, the aeration technology employed in the new Micro-Particle Colloidal Silver Generator keeps the silver particles uncommonly small throughout the entire colloidal silver-making process. You don't get progressively larger silver particles during the colloidal silver-making process, because the aeration suppresses excessive electrical conductivity throughout the entire process.
While there are other factors that make the new Micro-Particle Colloidal Silver Generator superior to standard colloidal silver generators, the above-described factors are the most important ones.
Colloidal science has come a long way in the past few decades. Perhaps the most important area of study has been with the "phase transition" of colloids. Phase transition is a term used to describe how colloidal particles can self-assemble into a variety of ordered phases. Simply put, it is the ability to form `complex ions' that can successfully interact with cellular membranes in the human body. The study of colloidal phase transitions is currently an area of intensive scientific research. One reason for all the hoopla is because of a better understanding of the molecular architecture of -- and biochemical processes within -- cellular membranes.
Cellular membranes play important roles in all living organisms. One can think of a cellular membrane as a door with a lock. In order for a substance to pass or interact with the membrane, it needs a key. The mechanism (key) that controls this is the molecular architecture of the particular substance. If the key fits, the substance can pass or interact. This area of study has lead to the development of more potent and effective pharmaceuticals, for example.
Silver (Ag) is known as a `transition element'. This means it has good phase transition characteristics, because of its ability to form stable complex ions. This gives silver the "potential" to interact with cellular membranes in the same way as other important complex ions such as vitamin B-12, chlorophyll, and the heme component of hemoglobin, in which the central metal ions are cobalt, magnesium, and iron. All of these, and many other important nutrients, are complex ions. However, in order for a silver particle to be as freely interactive in the body as a natural complex ion like vitamin B-12, it must have the same characteristics as B-12. Meaning it must be very small (nanoparticle) and have a stable electric charge. These are the fundamental principles on which the new Micro-Particle Colloidal Silver Generator was designed.
The patent-pending Micro-Particle Colloidal Silver Generator is a true nano-particle colloid system. A nano-particle (aka micro-particle) colloid system is any process that produces ultra-small colloids, less than 1 nm or .001 microns, with a stable electrical charge. While most colloidal silver generators cannot meet that standard, the new Micro-Particle Colloidal Silver Generator far surpasses that standard by producing silver particles as low as .0008 microns in size, and leaving them with a strong and stable electrical charge. What's more, the electrical charge on the tiny silver micro-particles is so strong, the silver remains in suspension in solution indefinitely. Most other colloidal silver generators produce significantly larger silver particles that hold a comparatively weak electrical charge. This leaves the silver particles "precipitating," or falling out of suspension in the solution within a matter of weeks or months at most.
In short, the new Micro-Particle Colloidal Silver Generator simply cannot be matched by standard colloidal silver generators. We hope this adds to your understanding of what makes the Micro-Particle Colloidal Silver Generator so much more beneficial than the standard colloidal silver generators being sold today.
[IMPORTANT NOTE AND DISCLAIMER: We are not doctors. We are distributors of electronic appliances and nutritional supplements. Therefore we cannot and do not offer medical advice. Please do not call with medical questions. If you have a medical problem, please see your licensed physician. Self-treatment is not recommended. The FDA has not evaluated the information contained on this web site. Products distributed by The Silver Edge are not intended to diagnose, treat, cure or prevent any disease. Testimonials are the subjective experiences of our customers and are not intended to be construed as being prescriptive in nature, nor a guarantee that the usage methods described are safe, effective or reliable, nor a guarantee that your results will be the same; individual results may vary. Additionally, the contents of this web site are strictly for information purposes only, and should not in any way be construed as providing or attempting to provide medical advice. Information on this web site is derived from sources deemed to be accurate and reliable, but no guarantee, express or implied, can be made regarding the accuracy or reliability of same. Therefore readers are encouraged to verify for themselves and to their own satisfaction the accuracy and reliability of all reports, recommendations, conclusions, comments, and opinions. The Silver Edge does not make any claims or promises as to health benefits accruing from the use of any product. There is plenty of publicly available independent documentation -- both pro and con -- regarding the uses and efficacy of colloidal silver and its long history in health and medicine. For a comprehensive overview, you may want to obtain a copy of The Ultimate Colloidal Silver Manual (547 pages, from Life & Health Research Group, LLC, 1-888-846-9029). Or see the link above to "Some Interesting Sources of Information on Colloidal Silver." Colloidal silver generators are electronic appliances designed to produce high-quality silver colloid. They are not medical devices. The Silver Edge specifically disclaims responsibility or liability for any loss or hardship that may be incurred by the reader as a result of the application of any information included on this web site, or as a result of the use or misuse of any electronic product or nutritional supplement. You are solely responsible for your health and nutrition choices. Anyone with additional information on colloidal silver is encouraged to write to The Silver Edge at the address directly below, so that it can be shared with others who may be interested.]
P.O. Box 84910
Phoenix, AZ 85071
Phone Orders/Customer Service: 1-888-528-0559 (M-F, 9am to 5pm AZ time)
FAX Orders: (602) 943-2363 (24 hours a day)
Tech Support: (760) 253-2988 (M-F 9am to 5pm CA time)
Email Sales/Customer Service: firstname.lastname@example.org
Email Tech Support: email@example.com
Copyright 2016. No reproduction without the expressed written permission of The Silver Edge.